Smooth interior hydraulics
Design around a smooth bore and shop-fabricated fittings.
- Manning’s n of 0.012, matched to RCP
- Curvilinear alignment around obstacles
- Tees, wyes, elbows, manifolds shop-fabricated
Specify a spiral rib storm sewer with a smooth interior and exterior structural ribs. We help you match diameter, coating, and installation requirements to your project.
The low-cost alternative to concrete pipe.
The spiral rib profile combines a smooth interior for hydraulic performance with exterior box ribs for structural strength. Select pipe gage and cover limits using project-specific design requirements.
Manning's n = 0.012 — the same hydraulic efficiency as reinforced concrete and smooth-wall plastic, so a smaller pipe often carries the same flow.
The 3/4″ rib profile delivers structural strength shown to be equivalent to RCP — with heights of cover that exceed both concrete and plastic.
Design around a smooth bore and shop-fabricated fittings.
A flexible steel system that carries load and moves with the soil — instead of cracking in settlement and poor ground.
Longer lengths and QUICK STAB® joints mean fewer joints, lighter equipment, and a lower number at the bottom of the bid.
| Criteria | Reinforced concrete | ULTRA FLO® | Plastic, HDPE/PP |
|---|---|---|---|
| Hydraulic efficiency (Manning's n) | 0.012 | 0.012 – equal | ~0.012 |
| Handling weight | Heaviest | Under 10% of comparable RCP | Light |
| Height of cover | High | Greater than RCP or plastic | Limited |
| Behavior in poor/settling soil | Rigid — cracks | Flexes & adapts | Flexes |
| Standard length / joint count | Short — many joints | 20–40 ft — fewer joints | Moderate |
| Service life (proper coating) | Long | 75–100+ years | Long |
Compare equivalent diameters, design loads, installation conditions, and applicable specifications. Consult the linked Contech comparison literature for product-specific details.
Over a 240-ft storm sewer run, longer ULTRA FLO sections mean far fewer joints to make in the field — less time in the trench, less equipment, less risk..
240 ft ÷ 40 ft = 6 sections
240 ft ÷ 8 ft = 30 sections
Illustrative comparison using the stated section lengths. End connections are excluded; supplied lengths and site conditions vary.
A zinc coating option for corrugated steel. The most economical metallic coating for corrugated steel.
Hot-dipped in pure aluminum for maintenance-free service life.
Predictable life in corrosive environments and municipal sewers. .
Heavy-gage polymer protects against abrasion and corrosion.
Service life depends on site exposure, abrasion, soil and water chemistry, material, coating, and maintenance. Confirm project-specific selection with Contech.
Start with your design flow, slope, cover, loading, and soil and water conditions. We can help you review pipe sizing and material or coating options against those inputs. Confirm the final selection against the applicable specifications and the current Contech product literature.
Using 40-ft sections, a straight 240-ft run contains six sections and five internal joints. Using 8-ft sections, the same run contains thirty sections and twenty-nine internal joints. These counts exclude end connections, fittings, and other changes in alignment; actual supplied lengths may vary.
Use the technical-document links in the design-tools section to review the ULTRA FLO brochure, comparison fliers, and CMP Design Guide. Check the edition and applicability before specifying. Your local Contech contact can help identify documents relevant to your material, coating, loading, and installation conditions.
Share the proposed alignment, pipe diameters, quantities, cover, loading, fittings, joint requirements, and material or coating preferences. Include drawings and known site conditions where available. Use the request-pricing or start-a-project links to begin the discussion; our team can help identify any additional design information needed.
Review design flow, diameter, gage, and coating with Contech engineering support.
Start a project →Access product literature and the CMP Design Guide for your specification review.
Technical documents →Review ULTRA FLO comparison literature alongside your project’s design requirements.
Get the comparisons →*Product specifications shown above are supplied in the design brief. Confirm current sizes, lengths, weights, joints, and availability in the product literature before specification.
Discuss site conditions and product selection with our team.
Review flow requirements, pipe sizing, and hydraulic performance.
Evaluate cover, loading, and foundation considerations.
Request pricing for your proposed system.
Discuss drawings and submittal needs for your project.
Coordinate preconstruction meetings, delivery, and installation support.
Share your design flow, cover, alignment, and site conditions. We’ll help you evaluate pipe sizing, coating options, and project pricing.

Contech® Engineered Solutions · Manufacturing America's Infrastructure™